Skip to content

Comfort & savings

Modulating boilers in Brussels: how this setting adjusts output continuously

A modulating boiler doesn't fire at full power in one go like an on-off model: it continuously adjusts its output to match actual heat demand. We explain what this means in practice for comfort and temperature stability in a Brussels home.

By DPS Chauffagiste · Published on 14 November 2026 · 7 min read

This article was translated from French.

Two very different ways of heating a home

When people think of a boiler, they often picture it working like a switch: it turns on, heats at full blast, then switches off once the desired temperature is reached. That is indeed how a so-called "on-off" boiler works. But a large proportion of the boilers installed today in Brussels work differently: they are modulating, meaning they can adjust their combustion output continuously, between a minimum and a maximum, rather than simply switching between two states.

At DPS Chauffagiste, we install and service this type of appliance very regularly in homes and flats across Brussels, and we find that the difference in everyday comfort is often more noticeable than residents expect. Let's explain what this setting actually changes.

How an on-off boiler works

A conventional non-modulating boiler works in cycles. As soon as the water or air temperature drops below the set threshold, the burner fires up at full power. It stays at this level until the target temperature is reached, then switches off completely. This cycle then repeats itself, over and over, throughout the day.

This way of working has a fairly easy-to-understand drawback: the output delivered almost never matches exactly what the home actually needs at a given moment. On a mild mid-season day, when the house only needs a small boost of heat, the on-off boiler will still start up at full power, heat more than necessary, then stop abruptly. The result is noticeable temperature swings, frequent on-off cycles, and faster wear on certain components that are subjected to these repeated start-ups.

The principle behind modulation

A modulating boiler, on the other hand, is fitted with a burner capable of varying its gas (or heating oil) flow rate, and therefore its output, according to what the heating demand actually calls for. In practice, if the house is losing little heat because it's mild outside, the boiler will run at a low setting, sometimes very close to its technical minimum. If it gets colder, it gradually increases its output, without jumping abruptly from fully off to full load.

This modulation range varies from one model to another: some boilers can drop to a fairly small fraction of their rated output, while others have a narrower range. In all cases, the central idea remains the same: instead of working in fits and starts, the appliance constantly seeks a balance between what it produces and what the home needs.

This setting is controlled by a sensor that measures the outdoor temperature, often combined with a room sensor, and by an electronic control board that calculates the required output in real time. This is known as weather-compensated control based on the heating curve: the boiler "anticipates" needs rather than simply reacting after the fact to a drop in temperature.

What this means for temperature stability

In a typical Brussels home, often made up of several rooms used in different ways, with façades exposed to varying degrees and insulation that varies depending on the age of the building, heating needs are never perfectly constant. Sun coming in through a south-facing window, a door left open for a moment, a radiator switched off in an unoccupied bedroom: all of this affects actual heat demand, minute by minute.

A modulating boiler adapts to these variations far more precisely than an on-off model. Rather than alternating between intense heating and a complete stop, it maintains a steadier, more gradually adjusted heat output. Residents generally feel a more stable temperature from room to room and hour to hour, without the small fluctuations that can be noticeable with a boiler that only has two speeds.

This isn't just a matter of thermal comfort in the strict sense: it's also about noise comfort. The repeated start-ups of an on-off boiler are often accompanied by a more noticeable start-up noise. A modulating boiler, which runs for longer periods at a lower setting, is generally seen as quieter in everyday use.

A way of working that is also easier on the system

Beyond the comfort it provides, modulation also affects how hard the appliance is worked. Every time a burner starts up, it places mechanical and thermal stress on the components: ignition, the rise in temperature, then cooling down when it switches off. A boiler that goes through many short on-off cycles puts more strain on these components than one that stays on for longer at a moderate output.

This doesn't mean a modulating boiler never switches off: it does, particularly when heat demand falls below its minimum output threshold, for example on a particularly mild day. But overall, the number of cycles is reduced compared with an on-off model operating under the same conditions.

Modulation and domestic hot water production

In combination boilers, which handle both heating and domestic hot water production, modulation also plays a noticeable role in the shower or at the sink. A boiler able to adjust its output continuously can better stabilise the hot water temperature during use, avoiding the sudden fluctuations that can sometimes be felt with a less responsive appliance.

Modulation and control: two complementary elements

It's worth noting that the burner's modulation capability only reaches its full potential when combined with suitable controls. A simple room thermostat, which merely switches the heating off and on again at a fixed threshold, doesn't make full use of a modulating boiler's capabilities. It's the combination with an outdoor sensor and, ideally, a weather-compensated or communicating thermostat that allows the appliance to calculate the most accurate output at any given moment, taking into account the actual outdoor temperature rather than just the measured indoor temperature.

This is something we check systematically during our visits: a modulating boiler poorly matched to its control system will never deliver everything it can offer in terms of stability and comfort.

Is this relevant to all Brussels homes?

Modulation really comes into its own in homes where heating needs vary significantly over the course of the day and the seasons, which is the case for the vast majority of houses and flats in the Region. Brussels terraced houses, with their front and rear façades exposed differently, or flats with varying solar gains depending on floor level and orientation, benefit particularly from this fine-tuning capability.

Some simpler systems or very small installations can manage perfectly well with on-off operation, without the difference being especially noticeable. But for most family homes, modulation provides a level of thermal balance that more basic appliances struggle to match.

A setting that needs to be checked and maintained

A boiler's modulation capability isn't something that's guaranteed forever: it depends on the burner being correctly set, the components being kept clean, and the sensors working properly. During the compulsory annual service, we check these parameters in particular, because a poorly adjusted burner can lose part of its ability to modulate properly, resulting in operation that becomes closer to on-off, even on an appliance that is technically modulating.

This service remains a legal requirement in the Brussels-Capital Region for gas and heating oil boilers, with a frequency that depends on the type of fuel. Beyond the regulatory aspect, it's also an opportunity to check that combustion is taking place correctly and safely, particularly with regard to the risk of carbon monoxide, a check we carry out systematically every time we visit.

Key takeaways

The difference between an on-off boiler and a modulating boiler isn't just an abstract technical matter: it's felt concretely in temperature stability, the noise level of the system, and the consistency of domestic hot water. For this modulation capability to be fully exploited, it needs to be paired with suitable controls and regular maintenance that ensures the burner setting remains correct over time.

If you're considering replacing a boiler, or if you'd like to check whether your current system is actually making the most of its modulation capability, the DPS Chauffagiste team is on hand to review your Brussels set-up and advise you on the settings best suited to your home.

Let's talk about your project

Tell us about your installation and we'll get back to you with a free quote.