Skip to content

Breakdowns & repairs

Boiler Firing Up Then Cutting Out Immediately: The Role of the Flame Sensor or Ionisation Electrode

Your boiler starts up, the flame appears for a few seconds, then everything stops abruptly. This specific symptom often points to the flame sensor or ionisation electrode, a safety component that shouldn't be cleaned as a DIY job.

By DPS Chauffagiste · Published on 8 November 2026 · 7 min read

This article was translated from French.

A specific symptom, not to be confused with other faults

The boiler starts up, you hear the burner ignite, sometimes you can even see the flame through the burner's sight glass, then everything stops. No rise in temperature, no prolonged sound of water circulating: just ignition followed by an almost immediate shutdown, within a few seconds. The appliance may retry several times before going into lockout, with a light flashing or an error code displayed on screen, depending on the model.

This behaviour is different from two other common faults it is sometimes confused with:

  • The classic short cycle, where the boiler heats for a while, stops, then starts again shortly after because the heat demand is met too quickly (incorrect output setting, faulty expansion vessel, poorly balanced circuit). In this case, the flame does have time to heat the water before going out.
  • Shutdown due to overheating, where the safety thermostat cuts off the appliance because the water temperature exceeds a critical threshold, generally after a longer period of operation, often linked to a lack of water circulation (blocked pump, closed valve, sludge build-up in the circuit).

When the shutdown occurs almost instantly after ignition, before the boiler has had time to produce any useful heat, the problem is almost always located at the level of flame detection itself: the boiler "believes" there is no flame, or loses this information too quickly, and cuts off the gas supply as a safety measure.

The role of the flame sensor or ionisation electrode

Every modern gas boiler is fitted with a system that continuously checks, while the appliance is running, that the flame is present and stable. This role is carried out either by a flame sensor (also called an ionisation electrode) or, on older models, by a photoresistive cell that detects the light given off by the flame.

The principle behind the ionisation electrode is simple yet clever: placed directly within the burner flame, it makes use of the fact that a gas flame ionises the surrounding air, making it slightly electrically conductive. The boiler's electronics send a very weak current through this electrode and measure the return signal. If the signal is present and stable, the boiler considers the flame to be burning correctly and keeps the gas supply on. If the signal disappears, weakens or becomes unstable, the control board interprets this as an absence of flame and immediately cuts off the gas, as a safety measure, to avoid any risk of unburnt gas leaking.

It is precisely this mechanism that explains the symptom described above: the boiler does ignite the gas, the flame appears, but the sensor fails to reliably confirm its presence. The result: an immediate shutdown, often within mere seconds, well before an overheating or water circulation problem would have had time to show up.

Why the sensor loses the signal: fouling and incorrect positioning

Two main causes account for the vast majority of cases of this kind.

Fouling of the electrode

Over successive combustion cycles, fine particles of soot, oxides or combustion residue gradually build up on the tip of the electrode. This layer, even if thin, acts as a partial electrical insulator, disrupting the measurement of the ionisation current. The signal becomes too weak or too irregular for the boiler's electronics to validate it, even though the flame is, in fact, perfectly normal. It is a bit like a clean, reliable sensor suddenly being "blinded" by dirt building up on its sensitive surface.

This fouling is gradual: it is not unusual for the boiler to keep working intermittently before shutting down completely, with increasingly frequent cut-outs over several weeks, until the day ignition fails every single time.

Incorrect positioning of the electrode

The electrode must sit at a very precise distance from the flame and the burner, defined by the manufacturer down to the millimetre. If it has shifted slightly — following poorly carried out maintenance work, a knock, repeated thermal expansion that wears out its mounting, or simply wear over time — it no longer sits correctly within the active zone of the flame. The ionisation signal then becomes insufficient, even on a perfectly clean electrode.

In some cases, both problems combine: a slightly misaligned electrode becomes more sensitive to fouling, because it picks up a weaker signal from the outset, and the smallest additional build-up is enough to push it below the validation threshold.

Why this component should not be cleaned without precautions

The flame electrode or ionisation sensor sits directly in the path of the gas and combustion, right next to the burner. Working on it necessarily means opening the combustion chamber, which can only be done safely under specific conditions:

  • The gas supply must be shut off beforehand, at the main shut-off valve, not simply by switching off the boiler. Working on the burner with the gas still on carries a real risk of leakage.
  • The power supply must also be switched off, to avoid any risk of electric shock and to allow components to be removed without accidentally triggering an ignition cycle.
  • Repositioning the electrode must follow the manufacturer's specifications, documented in the appliance's technical manual. A difference of just a few millimetres is enough to reproduce the problem, or even cause incomplete combustion if the electrode ends up too close to or too far from the optimal zone.
  • After any work on the gas circuit, a tightness (leak) check is essential before putting the appliance back into service, in line with the safety requirements governing gas installations in the Brussels Region.

For all these reasons, this operation is a job for an approved heating engineer, not a DIY task, however simple it may seem. It is not so much the technical difficulty of the cleaning itself that matters — gently rubbing an electrode with fine abrasive paper is nothing complicated in itself — but rather the conditions under which the operation must take place: correctly shutting off the supplies, checking for leaks, and testing combustion after reassembly. An undetected gas leak or an incorrectly repositioned electrode can have far more serious consequences than a boiler that refuses to start.

What a heating engineer does to fix this problem

When we deal with this type of fault, the process generally follows these steps:

  1. Diagnosing the error code displayed by the boiler, which often points directly to a flame detection fault.
  2. Safely shutting off the gas and electricity before opening the combustion chamber.
  3. Visually inspecting the electrode: condition of the tip, presence of deposits, any cracks in the ceramic insulator (a cracked electrode must be replaced, not just cleaned).
  4. Careful cleaning if fouling is the likely cause, using a suitable product or material that won't scratch the metal surface.
  5. Checking and adjusting the position according to the manufacturer's specifications, using a gauge if necessary.
  6. Reassembling, checking for leaks and testing combustion to make sure the appliance starts up normally and remains stable over several cycles.

If the electrode is too worn, cracked, or if its wiring is damaged, replacement is the most reliable solution: it is a standard, inexpensive part, and replacing it avoids facing the same problem again a few weeks later.

A symptom that highlights the value of regular servicing

This type of fault illustrates well why the compulsory annual servicing of a gas boiler in Brussels is not just an administrative formality. During this visit, the technician systematically cleans the flame electrode, checks its position and verifies the quality of combustion. Fouling that develops gradually is thus spotted and dealt with before it causes a complete breakdown of the appliance, often at the worst possible moment, in the depths of winter.

If your boiler shows this specific symptom — ignition followed by a shutdown within a few seconds, repeating every time you try — it's best not to keep trying to restart the appliance over and over. After a certain number of failed attempts, most boilers lock into safety mode and display an error code that will need to be reset after a repair in any case. Calling in a heating engineer makes it possible to quickly identify whether the flame sensor really is the cause, and to carry out the repair under safety conditions that simply cannot be improvised.

Let's talk about your project

Tell us about your installation and we'll get back to you with a free quote.